CAMremote-1 Ordering
The CAMremote-1 can be customized for different setups depends on camera model, photographing method, used equipment, power source etc. Several examples are here.Standard set of the CAMremote-1 contains:
- CAMremote-1 Controller
- CR-PC USB Configuration Cable (not for camera!)
- 3 JR/Futaba-style Cable
Note - it does NOT contain cable for camera control.
Following cable options are available depending on camera model and method how you intend to control the camera:
- CR-Camera USB Cable for Canon cameras if you intend to use USB/PTP or USB/CHDK method*
- Infrared (IR) Cable if you
intend to use infrared
triggering method
* More detail can be found in the CAMremote-1 Users Manual.
Use Add special instructions to seller field to enter your specific needs during checkout on PayPal page or send message using Contact page.
Users Manual and configuration software that are available electronically here aren't subjects of shipping.
All products have 30-day money back guarantee (excluding shipping costs) if you find that device doesn't meet to your expectations.
Still questions? Ask here.
Standard Set of the CAMremote-1
Standard set of
CAMremote contains the CAMremote-1 Controller,
CR-PC USB Configuration Cable (USB A-type) and 3
JR/Futaba-style Cables (with 3-pin female terminals,
default length 15cm/5.9" - 2g/cable, optional
30cm/11.8" - 3.3g/cable). Note - Standard Set does NOT contain cable for camera control, choose suitable cable below.
 |
74 EUR |
|
CR-Camera USB Cable for Canon, Nikon dSLR or Ricoh GX-series Cameras
CR-Camera USB Cable for Canon PowerShoot/dSLR, Nikon dSLR or Ricoh GX-series cameras (USB Mini-B
type plug)
if you intend to use USB/PTP or USB/CHDK method (default length
1-2cm/1.2" - 4g, optional 20cm/7.9" - 8g, optional 40cm/15.7cm - 12g).
Type of suitable USB
connector on camera is also shown in the
following figure. Be sure your camera have same connector! This is not suitable Nikon Coolpix-series cameras!
 |
5 EUR |
|
CR-Camera USB Cable for Nikon Coolpix Cameras
CR-Camera USB Cable for Nikon Coolpix-series cameras (USB Mini-B
type plug)
if you intend to use USB/PTP method (default length
1-2cm/1.2" - 4g, optional 20cm/7.9" - 8g, optional 40cm/15.7cm - 12g).
Type of suitable USB
connector on camera is also shown in the
following figure. Be sure your camera have same connector!
ITEM IS COMING SOON! |
7 EUR |
|
Cable with Infrared LED
Cable with Infrared LED if you intend to use infrared control method of the camera (default length 20cm/7.9" - 1g).
 |
8 EUR |
|
Plug with Infrared LED
Short plug with Infrared LED if you intend to use infrared control method of the camera (length 1cm/0.4" - <1g). Useful when CR board is attached onto camera and IR plugin is toward to IR sensor of the camera.
 |
8 EUR |
|
Light Sensor Feedback Cable
Light Sensor Feedback Cable if you intend to use USB/CHDK method and would like to control the CAMremote using CHDK scripts (default length 15cm/5.9").
|
ITEM IS UNDER DEVELOPMENT
|
|
Motion Sensor
Passive Infrared Motion Sensor allows to trigger the camera shutter when motion is detected. Connect it to CAMremote using JR/Futaba-style cable provided with Standard Set. Wide supply voltage range from 3V up to 9V. Sensor is without shielding case as shown in picture.
 |
13 EUR |
|
9V Battery Cable
The 9V Battery Cable can be used to power the CAMremote (default length 15cm/5.9" - 2g). Battery connector is PP3 style.
 |
4 EUR |
|
JST/BEC Battery Cable
The JST/BEC-type (female) Battery Cable can be used to power the CAMremote (default length 15cm/5.9").
 |
4 EUR |
|
Y-type Servo Lead Extension Cable with Power Lead
The Y-type Servo Extension Cable with Power Lead can be used to add extra power input to CAMremote if all channels are occupied by servos (default length 13cm/5.1" - 4g). Default type of Power Plug is JST/BEC (female), PP3-type (9V) optional.
 |
6 EUR |
|
4-button Radio Control for CAMremote-1
The 4-button keyfob-size transmitter and receiver to control main functions of the CAMremote-1: shutter release, zoom in/out, lens open/close (only if camera supports it in USB/PTP or USB/CHDK mode). Radio frequency 433 MHz, output power 10mW, range up to 100 meters (outside). Receiver occupies 1 input channel only of the CAMremote. Power supply range of the receiver with CAMremote is 4-12V (higher voltage - better radio range). Transmitter has internal battery (included). Weight of the receiver 11g, size 55x25mm/2.2x1", default length of the cables 5cm/1.9".
 |
58 EUR |
Temporarily out of stock |
| Postal Insurance, EU only
(optional) |
5 EUR |
|
| Postal Insurance, non EU
(optional) |
27 EUR |
|
Payment and Shipping
Orders are processed by PayPal and may be paid from your PayPal account or by credit card. You will get confirmation e-mail from VP-Systems in 24 hours after purchase during business days.
Lead time is typically 3 to 8 days + delivery time.
Typical rate of shipping worldwide is 8 EUR and parcel will be
delivered as a registered Priority mail. Tracking is
available through Finland postal service in following countries: Belgium, Denmark, Germany, Iceland,
Ireland, Portugal, Sweden, Switzerland.
Tracking is probably available in other countries as well if your local post service offer tracking service. Visit web page of your local post service and enter parcel ID number into their tracking system.
Delivery from Finland to Europe takes about 3-6 days, to USA 5-8 days or even more due to customs.
Tracking is probably available in other countries as well if your local post service offer tracking service. Visit web page of your local post service and enter parcel ID number into their tracking system.
Delivery from Finland to Europe takes about 3-6 days, to USA 5-8 days or even more due to customs.
Optional postal insurance is 5 EUR (European Union) and 27 EUR (outside European Union).
Buyer is responsible for all applicable customs, import duties, and VAT.
Still questions? Ask here.
28-Sep-2008
(c) 2008 VP-Systems